If you have examined some of the x86 assembly examples in the book of Hamacher et al., you may have noticed that there is a difference between the x86 assembly they use and the one used in this course. A brief explanation is in order here.
There is no such thing as an "official" x86 assembly language. In theory, you could write some custom x86 assembly and come up with a new syntax of your own (with the only small issue that now you would also need to write an assembler for that language). In practice, however, there are only two flavors of the x86 assembly language which are in actual use:
The Intel syntax, as used in the book, is the syntax used and developed by the Intel Corporation, the designers of the x86 architecture. It is the syntax that you will see in the official x86 reference manual and platform definition. If anything, this could be considered the "official" x86 syntax.
Long before the Intel Corporation introduced the x86, however, there was the UNIX operating system and the programming language C, both of which were developed at Bell Labs, the R&D department of the American phone company AT&T. Bell Labs and others had ported the UNIX operating system to a variety of different architectures before the x86 even existed, and thus the AT&T-style of assembly languages was widespread long before the x86 came along.
While Intel may favor its own syntax, learning the AT&T syntax could be considered more beneficial; There are many other AT&T-style assemblers available for various hardware architectures and most compilers generate AT&T-style output. Some may even argue that the AT&T syntax is more elegant than Intel's but let's not start that discussion.
Below are some of the most notable properties of the AT&T syntax that should give you a basic understanding of the instruction formats.
Do not worry if many parts or examples are still somewhat cryptic to you - many of the concepts will be explained in the remainder of this Manual, however, you have to start somewhere, and explaining the basics of the syntax is not really possible without, well, using the syntax in some way.
Direction / Order of OperandsWhile the instructions in the Intex syntax are of the form op dst, src, so listing the destination operand before the source operand, the AT&T syntax is more naturally readable from left to right by reversing this order and listing the source before the destination.
movq%rax, %rbxThis instruction in the AT&T syntax copies (or "moves") the value from the rax register (left) to the rbx register (right), so as you would read from left to right. The same instruction in the Intel syntax would be:
mov %rbx, %rax InconveniencesWhile this "reading direction" applies to most instructions in the AT&T syntax, there are some exceptions to it. For example the sub instruction:
subq%rax, %rbxIntuitively, many would read this as something like rax−rbx\texttt{rax} - \texttt{rbx}rax−rbx. However, that is not the operation that is performed. The sub instruction subtracts the source operand from the destination operand. Thereby, this line actually computes rbx−rax\texttt{rbx} -\texttt{rax}rbx−rax and stores the result in rbx.
Similarly, as the cmp instruction for comparing two values is nothing more than a subtraction that discards the result, the following lines might be equally confusing:
cmpq$1, %rax# compare the value 1 to the contents of raxjg somelabel# jg -> jump if greater thanIntuitively, this condition could be read as "jump if 1>rax1>\texttt{rax}1>rax", however, here again, the reading order has to be reversed. This actual condition is "jump if rax>1\texttt{rax} > 1rax>1".
For now, it is sufficient to know about these properties. However, once you have gained some experience in Assembly programming, you might want to investigate the reasons why the syntax of conditional jumps is so inconvenient in this syntax.
Instruction PostfixesMany instructions in AT&T syntax need to be postfixed with a b, w, l, or q modifier. This postfix specifies the size of the operands, where
b stands for "byte",
w stands for "word" (2 bytes),
l stands for "long" (4 bytes),
and q stands for "quadword" (8 bytes).
As an example, take a look at the four different uses of the mov instruction:
movb$1, %al # move value 0x01 to register almovw$1, %ax # move value 0x0001 to register axmovl$1, %eax# move value 0x00000001 to register eaxmovq$1, %rax# move value 0x0000000000000001 to register raxEven though you may "default" to using quadwords in most situations, always make sure to consider whether that is the right choice. Some assignments might require different sizes to be used, and will only pass the tests if those sizes are respected.
PreviousA Brief History LessonNextMemoryLast updated 2 months ago